□ 실험 목적
○ 가속도계를 이용하여 진동 측정 실험을 수행.
○ 측정된 데이터를 Time domain, Frequency domain 별로 비교 분석
□ 이 론
○ 진 동
- 어떤 물체가 기준 위치에 대해 반복운동을 할 때 그 물체는 진동한다고 말함.
같은 시간 간격으로 되풀이 되는 모든 운동을 주기운동 혹은
1. 서론
날이 갈수록 발전하는 기술 속에서 인간은 삶의 질을 높이기 위해 계속적으로 노력중이다. 더 편안하고 조용한 삶을 영위하기 위한 인간은 소음 및 진동에 대한 고충이 늘어가고 있으며, 이러한 고충을 해결하기 위한 노력 또한 계속되고 있다. 이에 대한 방안으로 제진 기술이 요구된다. 최근
Investigate the relationship
between flow condition and
fluid velocity in order to
understand Reynolds
number in flow dynamics
A. Shear Stress
B. Viscous & Inertia Force
C. Reynolds Number
D. Laminar & Turbulent Flow
E. Type of flow
Shear stress slow down the motion so that the velocity close to the wall will reduce
→ velocity gradient (dy/dx)
shear stress)와 전단율 (shear rate)의 비율로 표현된다. 외부에서 가해지는 힘(스트레스)에 저항하는 정도를 말한다. 막대기로 점도가 서로 다른 유체를 휘젓는 것으로 그 저항(점도) 을 비유할 수 있다. 점도는 역학점도(dynamic viscosity)또는 절대점도 (absolute viscosity) 라고도 부르기도 하는데 이는 동점도(kinemat
Dynamic test)으로 분류된다. 정적 시험에는 정적 하중을 가하여 시험하는 것으로 정하중 시험이라고도 한다. 정하중 시험은 인장, 압축, 전단, 굽힘 및 비틀림 등의 강도 시험을 총칭한 것이다. 일반적으로 비교적 짧은 시간 내에 시험 목적을 달성할 수 있으나, 크리프 시험과 같이 긴 시간이 필요한 정적
Dynamic test)으로 분류된다. 정적 시험에는 정적 하중을 가하여 시험하는 것으로 정하중 시험이라고도 한다. 정하중 시험은 인장, 압축, 전단, 굽힘 및 비틀림 등의 강도 시험을 총칭한 것이다. 일반적으로 비교적 짧은 시간 내에 시험 목적을 달성할 수 있으나, 크리프 시험과 같이 긴 시간이 필요한 정적
shear force) F는 다음과 관계가 있다.
여기서 단위 면적당 전단력 F/A를 전단응력(sheer stress) τ 로 표시하고, 비례상수 를 도입하여 표시하면 위의 식은 다음과 같다.
위의 식에서 비례상수 를 점성계수(absolute viscosity, dynamic viscosity),를 속도구배(viscosity gradien
sheared off and the big screw
prangs the wall with an earsplitting K-K-KWANG!
INT. PORT TO TORPEDO ROOM 8
With the outer tube-doors torn off, seawater slams in, busting the inner
hatches. Two-foot thick columns of water, like fire-hoses of the gods,
blast into the room. Everything vanishes instantly in white spray.
INT. CONTROL RM/ATTACK CENTER 9
Everyone is hurled off his feet. The planesman fli
dynamic pressure(q_∞)와 chord(c)의 곱으로 나누어 양력계수(c_l)를 구한다.
단위 두께당 양력, 즉, Lift per unit span (L^')은 다음과 같이 구한다.
L^'=N^' cosα-A'sinα
N^':normal force per unit span
A^':axial force per unit span
α:Angle of attack
양력계수는
c_l=L^'/(q_∞ c)=L^'/(〖1/2 ρ〗_air u_∞^2 )c
로 나타낸다.
N^'과
position, skin thickness and taper ratio.
I Beam shape
4.2. I Beam
Beam theory shows that the I-shaped section is a very efficient form for carrying both bending and shear loads in the plane of the web. On the other hand, the cross-section has a reduced capacity in the transverse direction, and is also inefficient in carrying torsion.
4.3. Two spar structure
Two spar structure